Ways & How

How to Make Vintage Jewelry

How to Make Vintage Jewelry

Vintage jewelry can add an old world feel to any kind of outfit, whether it’s an elaborate costume or just casual jeans and a shirt. Moreover, because of the appeal of vintage, a lot of people love wearing vintage jewelry to show off their style. If you want to save money, you can learn how to make vintage jewelry on your own, such as vintage button bracelets and vintage button earrings. The great thing about these pieces of jewelry is that you can use loose buttons that you find at home. Vintage button bracelets

  1. Gather the following materials:

    A: Vintage buttons with shank backs

    B: Chain

    C: Charms

    D: Jewelry pliers

    E: Jump rings

    F: Lobster clasp

  2. Open the jump ring using jewelry pliers and slide a button onto it. Attach the jump ring to the chain. Repeat this process in order to attach the buttons to the chain.



    /p>

  3. Make sure that the number of buttons equals the number of links in the chain. If this is not possible, just make sure that the style is uniform, like a button every two or three links.

  4. For a basic design, start with the largest button in the middle of the bracelet, followed by mid-sized buttons on each side, and finally the smallest buttons near the lobster clasp.

  5. After attaching all the vintage buttons, attach a lobster clasp on one end of the bracelet chain, and a jump ring on the other. However, the jump ring is optional since you can just attach the lobster clasp on the chain link if it is big enough. This way, the vintage bracelet is adjustable. You may also attach a few charms before finishing off with the lobster clasp.

Vintage button earrings
  1. Gather the following materials and tools:

    A: 2 large matching buttons with a flat back

    B: 2 earring posts with clutches

    C: 2-part epoxy

    D: Cotton swab

    E: Acetone

  2. Cover your work area to prevent stains and messes.

  3. Squeeze out the two tubes of epoxy in equal amounts and mix them together for a few minutes on a disposable surface like a paper bowl. You can use a toothpick to mix them thoroughly. Take your time and don’t rush. Keep stirring until bubbles form in the mixture. Afterward, leave it be for a few minutes to let it thicken; otherwise, the mixture will be too watery to use. Usually, this requires around 15 minutes. However, don’t let it sit for more than 2 hours because it will harden.

  4. Take a cotton swab and dip it in acetone. Use it to clean the earring post and the buttons.

  5. After letting the epoxy thicken, apply some on the back of the earring post and attach the buttons to it. Let the earrings set for a while, but make sure that you check on it every now and then. One issue that could occur is the earring post might be sliding around a bit if the epoxy is still a little watery. In this case, you can make the necessary adjustments before the epoxy completely hardens. Wait around 3 hours before trying on the earrings to make sure that everything has set.

Starting with these ideas on how to make vintage jewelry, you can tweak them and actually use different materials, such as resin cabochons and beads in place of the buttons, to make different pieces of jewelry. You can use any excess materials around the house or buy them from craft stores. You’ll have a vintage jewelry collection in no time.

POST YOUR COMMENTS

Your email address will not be published. Required fields are marked *



WaysAndHow is an online community of brilliant "how to" article authors who are wholly dedicated in bringing you the best and most in-depth ...

Follow us tweets

  • Knowing how to apply for Medicaid online is probably the best and most convenient ...

  • Student loan is one of the most difficult debts to pay off, largely because you accrue most ...

  • Most people would say that one of the hardest parts in starting a business is getting new ...

whats new

Contact Us

Contact

Address: Triple E Holdings Ltd. P.O. Box 23475 Richfield, MN 55423-0475 USA